Hide the TV components & use your remote
April 20, 2021
Share this
After finishing up so many HUGE projects lately (the basement bookcase wall,
garage makeover and mud/laundry makeover) I'm back to focusing on some
smaller projects in our basement. I started one a couple months ago and left
it in the dust when I focused on the garage clean up. Oh look, a butterfly! 😂
Now I'm working to finish that up and a couple other smaller projects as well.
This was a quick one thankfully, and looks great! I've shared how to add metal sheeting to cabinet doors before, (you can see the fireplace makeover at our old house there) but this time it was even simpler. I figured I'd share how I did it.
Why add metal sheeting you ask? Well when you like to have electronic
components hidden away like me, it's best to give them some air flow. Otherwise they run hot and that wills shorten the life of the components. Also,
your remotes won't work through a wood cabinet door, but will through metal
sheeting.
You can also use an RF remote control system that allows you to keep your TV electronics in another room -- I'll add a link to that at the end of the post. We didn't want to use that because we use the voice controls often.
Here's a reminder of how this project ended up:
This is one of my favorite projects ever...I adore it.
I cut the back out of two of the bottom bench cabinets in preparation for
the electronics to be added later. We knew we'd have a receiver down there
at the very least, and I wanted to allow for more air flow and access from the backs of the cabinets.
A few weeks ago we had the first part of our sound system installed, and
every time we turned on the TV we had to open the cabinet to get the remote
to work. Then a cat or two would crawl back there...so I knew it was time to
get those door fronts replaced.
I removed the cabinet doors from the hinges and used a large drill bit to make
holes in the four corners of the front panel. This gives you a spot to
insert your jigsaw blade:
This post may contain affiliate links for
your convenience.
See my policies and disclosure page for more information.
I had plenty of spots that weren't perfectly flush:
I grabbed
my favorite little sander
and used a coarse grit pad to get those parts flush:
It worked really well! I cleaned all of that up and touched up the inside parts with the paint color,
Westchester Gray by Sherwin-Williams.
Last time I did this I used a silver metal sheeting with a dark gray on our
old fireplace built ins. This time I picked a brass/copper finish that
matched our brass hardware. These sheets come in a few colors and
designs.
Just figure out the size you'll need and then it can be cut with regular
scissors. This sheeting is very thin!
I used my stapler to secure the metal to the back of the cabinet
frame:
It went into the sheeting easily -- but you may have to pound the staples in
so they're flush with the wood.
The rough edges of the sheeting aren't crazy sharp -- I wouldn't rub my
fingers along them on purpose but they won't cut you just by touching it.
You can add some small trim over the edges if you are worried about those.
It looked even better than I expected! LOVE it:
You can find links to
the brass hardware I used here. I really like the design on these metal sheets -- it's called Lincane.
I know I say this all the time, but don't let anyone tell you you can have
both form and function. It just takes some creativity (or an internet
search!) to make it happen. :)
The remote works perfectly through the sheeting -- so no need to open the
doors anymore:
I'm considering adding
it to all three lower cabinets, but I don't really want to spend more money when I like it as it is! This stuff
isn't crazy expensive, but I can only get one door out of each sheet. You
can find these at most hardware stores or I'll share some online sources
below.
These sheets are a great option if you need remote control access in a built in unit, but they also just look great as a custom accent on any cabinet!
You can also use glass or cane if you'd rather not use the metal. Here are a
few options!:
This
metal mesh
would give you a modern look
Use this roll of
rattan cane for a traditional or transitional look
"Chainlink" metal design
in copper
"Lincane" metal design
like ours
Hide your devices out of sight with this RF remote control extender kit
See more of
our home here.
To shop items in our home,
click here!
Never miss a post by signing up to
get posts via email.
You are truly amazing! Always excited to see what you’ve done next. I just wish I could do this stuff too!
ReplyDeleteThank you so much! :)
DeleteLooks great! Where do you keep your DVD’s, video games, etc? (For upstairs and for downstairs)
ReplyDeleteVery cool! You know, as good as the gold tone looks, I think the sheeting would also look good painted the same color as the cabinets. I so admire your ability to create such beautiful and functional enhancements to your home.
ReplyDeleteHi. Where do I buy the mesh
ReplyDeleteYou can find it at most hardware stores -- I have good luck at Home Depot.
Delete